Showing posts with label shield. Show all posts
Showing posts with label shield. Show all posts

Wednesday, April 8, 2015

Weather Station - part I, sensor shield

Hi! I've been away for some time, but still doing things, just not publishing them as regularly as I would like to...
Well, but getting back to work , using some vase plates, of good plastic (they do not break when drilled) I managed to create a sensor shield, using 7 small plates, 2 bigger plates, 3 spacers like the ones on the right image and 3 screwed bars of 15 cm each. Drilled a big hole in the middle for a plastic tube on 6 of the small plates, leaving the big ones untouched  and on of the small ones. The objective is to create an insulated, rain free area inside the plates.
So, I have plastic plates, which the sun will possibly warm up during summer, but they are spaced allowing the air to flow and the sensors are inside an acrylic tube which is made of a rather different material preventing the warming up/cooling of the inside, hence, better isolation.
You can see on the left an almost finished view with a large plate, some small plates, a spacer and the acrylic tube. The finished piece is downside. It'll be painted on a more neutral color, like white or pale grey (I have a bottle of paint spray with this color, so why not use it? :D ).
The next step is to seal the upper and bottom holes with mosquito net, to assure I don't get unwanted guests inside, and then I'll wire cable from the arduino Mega box (possibly CAT5e which I have lots of spare meters) to connect the 2 (planned) sensors inside, a BMP085 barometric pressure and a HIH-4030 humidity/temperature sensor.
Afterwards I'll need another shield like this one for the luminosity sensor (hasn't arrived yet). A piezo will also be used to detect the rain intensity. The wind vane and anemometer will use a different housing.

Cheers!



Wednesday, March 18, 2015

Arduino ISP shield

Hi there! I finally managed to get the ISP shield on tracks, here you have some pictures, I just need some fresh ATmega328 to use it! :)

Initial circuit and pieces
Piezo soldered
Piezo and Leds in place
On top of the main board, quite nice ah?..
Downside, a little messy, but better hidden than at sight!!!

Friday, January 2, 2015

The TIP120 Arduino shield

  This article is about a homemade Arduino shield, using a TIP120. The TIP120 is a darlington transistor that works as an electronic switch, it can handle large power, such as 60 Volt, 5 Amp (for high power you should use an aluminum cooler). This approach has some advantages over a relay circuit, and some disadvantages too, as you all can imagine, one of the disadvantages is the use of 110/220V circuitry as the TIP only works with 60V, on the other hand you can use PWM on it, it is faster than a mechanic switch as the relay and I imagine it consumes lower power on switching than the relay.
I used the circuit on the right (which I found somewhere over the internet) to build a schematic as you can see on the image at the
right to build afterwards an Arduino shield.


At the top of the image we see the TIP and the Arduino connection, the Arduino signal (that can be a regular digital output with an on/off behavior, or a PWM digital output to provide dimming on a lamp/LED or motor) and the GND provided by the Arduino board. On the lower end of the schematic we have 2 board connectors, one for connecting the load with the polarity showed (the polarity is only important on devices which have one, in case of a DC motor the TIP is protected by a diode 1N4007 or similar) and the other to connect the power. The 1 k Ohm resistor should be replaced by a 4k7 because of ground fluctuations.
The final result can be seen in the pictures.



NOTE: Has been registered a situation where the input control pin had a fluctuating voltage and the load and power were connected leading the TIP to a ON false situation, a workaround could be increase the resistor value or ground the control pin. Not tested yet.


Wednesday, May 8, 2013

RTC shield, I²C, Arduino compatible, DIY

Hi! I'm back, again with arduino and a new shield, once more a DIY shield. 
So, let's start! The picture on the right is the circuit used to build the shield (I want to thank my friend Nuno Portela, who grabed this, and converted to eagle schematic, printing and driling the circuit afterwards).
The schematic on the left is the proposed circuit, which was then printed. All the components are easy to find, so the final result is almost inexpensive.
I've attached also a picture of the final result, 2 boards with cr2032 button cells. 
Concerning the code, I couldn't find where I got mine, so I'm posting it here.
Enjoy!

Saturday, April 27, 2013

Arduino DIY SD shield

Well... I got tired of having the arduino connected to the PC to have a logger, so did some search and ended up with this shield, it uses a micro SD card to SD converter, which is soldered to the board as you can see on picture, the components are easy to find, and they are used to low down voltage from the arduino pins (5V) to something near the 3.3V which is the correct voltage of the SD card. The red cross in the picture means you have to interrupt the circuit on those points, otherwise you would be short-circuiting the resistor. The numbers on the right (10,11,GND,3.3V,13,X,12) are the pins in the arduino board, 3.3V and GND I suppose you know what that means, and X is not connected and is used to align the plug, avoiding upside-down connections.
You can see on the left the final look, without the microSD card adapter:
And on the right side, the final look, already with the adapter soldered.

Enjoy!

 



Spoiler alert: DO NOT try to connect the card directly to arduino pins, without this voltage divider, you will damage the card!

Based on this shematic.

Test file here and another one here.

Friday, December 16, 2011

Arduino relay shield (homemade)

Hi! This is my homemade arduino relay shield, I had a spare 12V relay, and nothing to do with it, so this project happened.
The circuit is roughly the version seen in the schematic on the left, with a BC548 (NPN) transistor and a 1N4007 diode, my resistor was of 8220 Ohm.
The ground (GND) has to be the same on the arduino and on the relay shield, or it will not work.
On the picture you can see on the bottom part the + (Vcc), S (signal from arduino, any digital port), and - (GND), on top we see the connectors for NO, (normally opened) C, (common), NC (normally closed).
For the whole article, you can follow the original instructable that I based on, here.Link